• PipePlus96

PipePlus96

The PipePlus96 machine combines versatility, wide production range, high output and simplicity into one outstanding package. With its three station rotary design, the PipePlus96 will produce pipe in numbers never-before achieved. Three different pipe sizes are produced at the same time using small diameter EightPak molds, SixPack molds, Quad molds, Duo molds or Single molds depending on the diameter of pipe produced. Additionally, a quick fifteen minute changeover time further enhances manufacturing flexibility and permits short production runs of special or lower volumn products. The PipePlus96 uses the time proven vibration under pressure process to manufacture concrete pipe in sizes 300mm (12″) to 2500mm (96″) in lengths up to 3.5M (12′)

Product Range

  • Round Pipe Sizes – 300mm (12″) – 2500mm (96″)
  • PVC or PEHD Lined Pipe
  • Manhole Products
  • Bases – Riser Sections – Cone Sections – Flat Tops – Catch Basins
  • Non Round Products
  • Elliptical Pipe – Arch Pipe – Flat Bed Pipe – Box-shaped Products – And More….
  • Non Round Sizes
  • Minimum inside dimension – 300mm (12″)
  • Maximum outside dimension – Must fit within 3010mm (118.5″) diameter circle

Product Length

  • 2.5M Model – 0.3M (1′) to 2.5M (8′)
  • 3.0M Model – 0.3M (1′) to 3.0M (10′)
  • 3.5M Model – 0.3M (1′) to 3.5M (12′)

Pipe Form Capacity

  • EightPakform Configuration – Pipe sizes 300mm (12″) thru 450mm (18″)
  • SixPakform Configuration – Pipe sizes 300mm (12″) thru 600mm (24″)
  • Quadform Configuration – Pipe sizes 300mm (12″) thru 750mm (30″)
  • Triform Configuration – Pipe sizes 300mm (12″) thru 900mm (36″)
  • Duoform Configuration – Pipe sizes 300mm (12″) thru 1350mm (54″)
  • Singleform Configuration – Pipe sizes 300mm (12″) thru 2500mm (96″)

Pipe Joint Capabilities

  • Confined O-ring Rubber Gasket
  • Rolling O-ring Rubber Gasket
  • Profile Wedge Shape Rubber Gasket
  • Cast-in type Gasket
  • Mortar Joint
  • Mastic Joint
  • Butt Joint


  • 3-Station Turntable Principle
    Telescope your production processes for maximum efficiency.

    A traditional concrete pipe machine has (3) major processes –first the mold is filled, second the filled mold is pressed with a spigot former and finally the pipe is demolded. Utilizing the 3-Station principle, all these processes happen at the same time – multiplying the productivity!!


  • Exact length products
    Remove product variability by ensuring each product is exactly the same length. Many concrete pipe production machines are unable to accurately control the length of their products. Through a mixture of volumetric fill control, a proprietary pressheading process and precision mold quality, the PipePlus eliminates this inconsistency.


  • Header System
    Produce pipe with perfectly round, glass-like spigots – ensuring exact field pipe connections.

    Use of stay-in-place headers allows for the production of pipe with more precise male-end spigots with a smoother surface finish.


  • Synchronized Core Vibration (SCV)
    High-powered, built-in, electrically-driven core vibration system allows for the production of high-quality pipe and eases form changeover.

    In a SCV system, every form set has its own, built-in vibration system. The use of such a system gives the added benefit of eliminating the need to swap vibrators from core to core during changeover, eliminating the costly downtime and increasing plant flexibility.


  • Multiforms
    Easily multiply your production tonnages through the use of patented Multiforms. The PipePlus machines allow for the possibility of mass-production through the use of the Multiform system – allowing the producer to increase his output by 2x, 3x, 4x, 6x and even 8x –without significantly affecting cycle times.


  • Quick Mold Changeovers
    Be Flexible. Don't tie up your money in excess pipe inventory.

    Simple, machine-to-mold connections and self-contained mold modules allow for changeovers of less than 15 minutes on the PipePlus machines.


  • Semi-Automatic Operation w/ optional Smartchute
    Automate to save labor and achieve precisely repeatable production cycles, guaranteeing each product is as high-quality as the next.

    The PipePlus machines can be equipped with optional automatic presshead and vibration controls as well as a concrete distribution chute that automatically adjusts between pipe dimensions.


  • Optional Cast-In-Place manhole steps
    Eliminate costly & back-breaking labor required to drive steps into manhole products.

    The Cast-In-Place Step (CIPS) program allows for the automatic casting-in of manhole steps – including an automated step- insertion robot to keep machine operator working at a safe distance from the machine.


  • Optional lifting anchor automation
    Save labor costs by automatically casting lifting anchors into products during machine cycle.

    One of the most tedious and labor-consuming tasks in a manhole or pipe operation is the insertion and driving in of lifting anchors into already-cured products. Eliminate this step with an automated lift-anchor insertion system.